Official ICT switch settings
XBA-USD6 DIP switch settings
Every switch function from ICT’s own setting sheet (part number SWBZUS64000-R), transcribed into tables you can read on a phone at the machine. Rows marked factory default are how the unit ships.
| Function | SW1 | SW2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 |
|---|---|---|---|---|---|---|---|---|
| Reject USD 1 | ON | — | — | — | — | — | — | — |
| Accept USD 1factory default | OFF | — | — | — | — | — | — | — |
| Reject USD 5 | — | ON | — | — | — | — | — | — |
| Accept USD 5factory default | — | OFF | — | — | — | — | — | — |
| Reject USD 10 | — | — | ON | — | — | — | — | — |
| Accept USD 10factory default | — | — | OFF | — | — | — | — | — |
| Reject USD 20 | — | — | — | ON | — | — | — | — |
| Accept USD 20factory default | — | — | — | OFF | — | — | — | — |
| Reject USD 50 & 100 | — | — | — | — | ON | — | — | — |
| Accept USD 50 & 100factory default | — | — | — | — | OFF | — | — | — |
| Disable Bill Reject 4 Times BA Stop By 30 Sec | — | — | — | — | — | ON | — | — |
| Enable Bill Reject 4 Times BA Stop By 30 Secfactory default | — | — | — | — | — | OFF | — | — |
| Stack Banknote when Power-up | — | — | — | — | — | — | ON | — |
| Reject Banknote when Power-upfactory default | — | — | — | — | — | — | OFF | — |
| Reserved | — | — | — | — | — | — | — | ON |
| Reservedfactory default | — | — | — | — | — | — | — | OFF |
- This dip switch is located at the side of XBA.
| Function | SW1 | SW2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 |
|---|---|---|---|---|---|---|---|---|
| Inhibit Active HIGH / ccTalk: Table 1 / NISR: No ERROR CODE | ON | — | — | — | — | — | — | — |
| Inhibit Active LOW / ccTalk: Table 1 / NISR: Send ERROR CODEfactory default | OFF | — | — | — | — | — | — | — |
| Reserved | — | ON | — | — | — | — | — | — |
| Reservedfactory default | — | OFF | — | — | — | — | — | — |
| 50ms LO / 50ms HIfactory default | — | — | OFF | OFF | — | — | — | — |
| 50ms LO / 100ms HI | — | — | OFF | ON | — | — | — | — |
| 65ms LO / 75ms HI | — | — | ON | OFF | — | — | — | — |
| 100ms LO / 150ms HI | — | — | ON | ON | — | — | — | — |
| Reserved / NISR: Standard Mode | — | — | — | — | ON | — | — | — |
| Reserved / NISR: Customized Modefactory default | — | — | — | — | OFF | — | — | — |
| Credit-Pulse Normal HIGH / ccTalk: ccTalk 16-bit Encryption mode & Restore Mode (See Table.1)factory default | — | — | — | — | — | ON | — | — |
| Credit-Pulse Normal LOW / ccTalk: ccTalk 16-bit Decrypt mode & 8-bit checksum (See Table.1) | — | — | — | — | — | OFF | — | — |
| Pulse Mode / ccTalk: Pulse Mode / NISR: Pulse Modefactory default | — | — | — | — | — | — | ON | — |
| Other Mode / ccTalk: Other Mode / NISR: Other Modefactory default | — | — | — | — | — | — | OFF | — |
| 1 pulse / USD 1 / ccTalk: ccTalk Modefactory default | — | — | — | — | — | — | OFF | OFF |
| 2 pulses / USD 1 / ccTalk: RS232 A0 Mode | — | — | — | — | — | — | OFF | ON |
| 4 pulses / USD 1 / ccTalk: ICT104U Mode | — | — | — | — | — | — | ON | OFF |
| 20 pulses / USD 1 / ccTalk: NISR Mode / NISR: NISR Mode | — | — | — | — | — | — | ON | ON |
- This dip switch is located on the CPU board; remove the CPU board cover first.
| Function | SW1 | SW5 |
|---|---|---|
| 8-Bit Checksum | OFF | OFF |
| Restore mode (Note.1) | OFF | ON |
| CRC 16-Bit Decrypt Checksum | ON | OFF |
| CRC 16-Bit Encryption Checksum | ON | ON |
| Bill value | Pulse | ICT104U | NISR | ccTalk | RS232 A0 |
|---|---|---|---|---|---|
| BV1 | $ 1 | $ 1 | $ 1 | $ 1 | $ 1 |
| BV2 | $ 5 | $ 5 | — | $ 5 | — |
| BV3 | $ 10 | $ 10 | $ 5 | $ 10 | $ 5 |
| BV4 | $ 20 | $ 20 | $ 10 | $ 20 | $ 10 |
| BV5 | $ 50 | $ 50 | $ 20 | $ 50 | $ 20 |
| BV6 | $ 100 | $ 100 | $ 50 | $ 100 | $ 50 |
| BV7 | — | — | $ 100 | — | $ 100 |
Before you power up
- After setting dip switch of the credit pulses, you should reset the bill acceptor again.
- Turn this dip to with restart the bill acceptor will restore ccTalk address to its default value of 40 and the encryption key to its default value of 123456.
- Calibration card is needed.
Not the sheet for your unit?
ICT ships the same model with different firmware and currency sets. Send us a photo of the label on the side of the acceptor and we will tell you exactly which settings apply.