Official ICT switch settings
TAO-V-USD6 DIP switch settings
Every switch function from ICT’s own setting sheet (part number SWH5US64000-R), transcribed into tables you can read on a phone at the machine. Rows marked factory default are how the unit ships.
| Function | SW1 | SW2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 |
|---|---|---|---|---|---|---|---|---|
| Reject US$ 1 | ON | — | — | — | — | — | — | — |
| Accept US$ 1factory default | OFF | — | — | — | — | — | — | — |
| Reject US$ 5 | — | ON | — | — | — | — | — | — |
| Accept US$ 5factory default | — | OFF | — | — | — | — | — | — |
| Reject US$ 10 | — | — | ON | — | — | — | — | — |
| Accept US$ 10factory default | — | — | OFF | — | — | — | — | — |
| Reject US$ 20 | — | — | — | ON | — | — | — | — |
| Accept US$ 20factory default | — | — | — | OFF | — | — | — | — |
| Reject US$ 50 & 100 | — | — | — | — | ON | — | — | — |
| Accept US$ 50 & 100factory default | — | — | — | — | OFF | — | — | — |
| Reserved | — | — | — | — | — | ON | — | — |
| Reservedfactory default | — | — | — | — | — | OFF | — | — |
| Harness Disable (Other Mode: BA stops working when fishing) | — | — | — | — | — | — | ON | — |
| Harness Enable (Other Mode: Normal)factory default | — | — | — | — | — | — | OFF | — |
| Inhibit Active High | — | — | — | — | — | — | — | ON |
| Inhibit Active Lowfactory default | — | — | — | — | — | — | — | OFF |
| Function | SW1 | SW2 | SW3 | SW4 |
|---|---|---|---|---|
| 1 pulse / US$ 1factory default | OFF | OFF | — | — |
| 2 pulse / US$ 1 | ON | OFF | — | — |
| 4 pulse / US$ 1 | OFF | ON | — | — |
| 20 pulse / US$ 1 | ON | ON | — | — |
| Interface Timing Conversion — 50ms LO / 50ms HIfactory default | — | — | OFF | OFF |
| Interface Timing Conversion — 60ms LO / 300ms HI | — | — | ON | OFF |
| Interface Timing Conversion — 30ms LO / 50ms HI | — | — | OFF | ON |
| Interface Timing Conversion — 150ms LO / 150ms HI | — | — | ON | ON |
| Function | SW1 | SW2 | SW3 | SW4 |
|---|---|---|---|---|
| Credit-Pulse Normal HIGHfactory default | ON | — | — | — |
| Credit-Pulse Normal LOW | OFF | — | — | — |
| Pulse Modefactory default | — | ON | — | — |
| MDB Interface | — | OFF | — | — |
| Reserved | — | — | ON | — |
| Reservedfactory default | — | — | OFF | — |
| Reserved | — | — | — | ON |
| Reservedfactory default | — | — | — | OFF |
| Function | SW1 | SW2 | SW3 | SW4 |
|---|---|---|---|---|
| Scaling Factor (SF) = 100, Decimal Point Position (DPP) = 2factory default | ON | — | — | — |
| Scaling Factor (SF) = 1, Decimal Point Position (DPP) = 0 | OFF | — | — | — |
| Pulse Mode | — | ON | — | — |
| MDB Interfacefactory default | — | OFF | — | — |
| Reserved | — | — | ON | — |
| Reservedfactory default | — | — | OFF | — |
| Reserved | — | — | — | ON |
| Reservedfactory default | — | — | — | OFF |
| Bill value | Pulse | MDB |
|---|---|---|
| BV1 | US$ 1 | US$ 1 |
| BV2 | US$ 5 | — |
| BV3 | US$ 10 | US$ 5 |
| BV4 | US$ 20 | US$ 10 |
| BV5 | US$ 50 | US$ 20 |
| BV6 | US$ 100 | US$ 50 |
| BV7 | — | US$ 100 |
Before you power up
- (1) Reset the bill acceptor after setting the dip switch.
- (2) SW7 and SW8 of the 8-switch DIP and the 4-switch DIP are for pulse protocol only.
Not the sheet for your unit?
ICT ships the same model with different firmware and currency sets. Send us a photo of the label on the side of the acceptor and we will tell you exactly which settings apply.