Official ICT switch settings
LX7-A-USD6 DIP switch settings
Every switch function from ICT’s own setting sheet (part number SWCNUS610-R), transcribed into tables you can read on a phone at the machine. Rows marked factory default are how the unit ships.
| Function | SW1 | SW2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 |
|---|---|---|---|---|---|---|---|---|
| Reject USD 1 | ON | — | — | — | — | — | — | — |
| Accept USD 1factory default | OFF | — | — | — | — | — | — | — |
| Reject USD 5 | — | ON | — | — | — | — | — | — |
| Accept USD 5factory default | — | OFF | — | — | — | — | — | — |
| Reject USD 10 | — | — | ON | — | — | — | — | — |
| Accept USD 10factory default | — | — | OFF | — | — | — | — | — |
| Reject USD 20 | — | — | — | ON | — | — | — | — |
| Accept USD 20factory default | — | — | — | OFF | — | — | — | — |
| Reject USD 50 & 100 | — | — | — | — | ON | — | — | — |
| Accept USD 50 & 100factory default | — | — | — | — | OFF | — | — | — |
| Reserved | — | — | — | — | — | ON | — | — |
| Reservedfactory default | — | — | — | — | — | OFF | — | — |
| Harness Disable | — | — | — | — | — | — | ON | — |
| Harness Enablefactory default | — | — | — | — | — | — | OFF | — |
| Inhibit Active High | — | — | — | — | — | — | — | ON |
| Inhibit Active Lowfactory default | — | — | — | — | — | — | — | OFF |
| Function | SW1 | SW2 | SW3 | SW4 |
|---|---|---|---|---|
| ccTalk Parameters (default setting) (Note.4) | ON | — | — | — |
| ccTalk Parameters (User setting)factory default | OFF | — | — | — |
| 1 pulse / USD 1factory default | OFF | OFF | — | — |
| 2 pulses / USD 1 | ON | OFF | — | — |
| 4 pulses / USD 1 | OFF | ON | — | — |
| 20 pulses / USD 1 | ON | ON | — | — |
| Pulse Speed: 50ms LO / 50ms HIfactory default | — | — | OFF | OFF |
| Pulse Speed: 60ms LO / 300ms HI | — | — | ON | OFF |
| Pulse Speed: 30ms LO / 50ms HI | — | — | OFF | ON |
| Pulse Speed: 150ms LO / 150ms HI | — | — | ON | ON |
| Function | SW1 | SW2 | SW3 | SW4 |
|---|---|---|---|---|
| Pulse Normal Highfactory default | ON | — | — | — |
| Pulse Normal Low | OFF | — | — | — |
| Pulse Modefactory default | — | ON | — | — |
| ccTalk Interface | — | OFF | — | — |
| Reserved | — | — | ON | — |
| Reservedfactory default | — | — | OFF | — |
| Reserved | — | — | — | ON |
| Reservedfactory default | — | — | — | OFF |
| Function | SW1 | SW2 | SW3 | SW4 |
|---|---|---|---|---|
| 8-bit checksum | ON | — | — | — |
| CRC 16-bit checksumfactory default | OFF | — | — | — |
| Pulse Mode | — | ON | — | — |
| ccTalk Interfacefactory default | — | OFF | — | — |
| Reserved | — | — | ON | — |
| Reservedfactory default | — | — | OFF | — |
| Encryption MODEfactory default | — | — | — | ON |
| Decrypt MODE | — | — | — | OFF |
| Bill value | Pulse | ccTalk |
|---|---|---|
| BV1 | USD 1 | USD 1 |
| BV2 | USD 5 | USD 5 |
| BV3 | USD 10 | USD 10 |
| BV4 | USD 20 | USD 20 |
| BV5 | USD 50 | USD 50 |
| BV6 | USD 100 | USD 100 |
Before you power up
- Default setting.
- Use 2nd and 3rd dip of the internal dip-switch to change different interface protocol.
- Turn this dip to with restart the bill acceptor will restore ccTalk address to its default value of 40 and the encryption key to its default value of 123456. (ccTalk ONLY)
Not the sheet for your unit?
ICT ships the same model with different firmware and currency sets. Send us a photo of the label on the side of the acceptor and we will tell you exactly which settings apply.